You know that wall you’ve been staring at? The one that needs a little something, or can serve a greater purpose? Installing some board and batten moulding may be exactly what you need to add a little style and some utility to an underused space.
STEP BY STEP INSTRUCTIONS FOR A 6-FOOT WALL OF MOLDING
COMPLETION TIME: 1-2 days | SKILL LEVEL: Moderate | TOTAL COST OF MATERIALS: $106
Let’s assume you want to make a 6-foot wide section of board and batten molding for 9-foot ceilings (if you
MATERIALS & TOOLS NEEDED FOR BOARD AND BATTEN
For a full list of materials and tools, just expand the lists below. If you do projects like this a lot, you should already have a lot of it. But I like to get everything out and organized so there are no unplanned trips to the hardware store.
STEP 1: MARK YOUR MEASUREMENTS AND MAKE SURE EVERYTHING IS CUT AC
It’s not all that fun, and may not seem to be productive, but double checking your measurements is soooo worth it. For these reasons, and probably even more I’m not thinking of:
- You can see if you like the way the measurement suite your space. This is a customizable project, feel free to tweak according to your taste!
- You will be sure of where the boards are sitting, so you know where the gaps in the sheets of plywood or masonite can lie without being seen. This will also be where you want to nail in your masonite so you don’t have to fill more nail holes.
[button link=”#get-your-own-measurements” size=”small” color=”blue” rounded=”false” ]Learn How to Customize These Measurements[/button]
STEP 2: CUT DOWN ALL YOUR MATERIALS
If you really are after a 6-foot section of board and batten, just follow the measurements listed above (also listed in the materials). The good news is, all the cuts are straight, so you don’t have to worry about any angles lining up.
Once you’ve cut your boards down, lay them out and make sure everything lines up and will fit your wall.
STEP 3: PREPARE THE WALL AND INSTALL THE MASONITE SHEETS
We used plywood that we had leftover from another project, which is why we have those gaps in the masonite. It was a “let’s make this work” situation. However, plywood is a lot more expensive. If I were buying materials from scratch for this, I would get 1/8″ masonite sheets for a fraction of the price ($8 vs. $35 per sheet).
To attach the sheets of masonite, nail it up in vertical rows where the boards are going to cover the nail holes. This is where having your vertical boards marked on the wall comes in handy.
Again , we had to use preexisting materials, so we had 3 strips instead of 2.
This is honestly the trickiest part. Once you get through this part, it’s smooth sailing…that’s a lie, but it’s the most important part.
STEP 4: INSTALL
INSTALL THE BASEBOARD: Use one of the 1×6″ boards as the new baseboard. Nail the board every 6 inches or so on top and bottom to secure it to the wall. (vertically level).
INSTALL THE VERTICAL BOARDS: We nailed up the long, 1×4″ boards from left to right making sure each board is plumb (vertically level).
ATTACH THE HEADER AND CAP: Attach the
Over the header, lay the 1×2″ board flat over the top of it and nail it from the top into the header board.INSTALL THE
STEP 5: PREPARE THE MOLDING TO PAINTSET AND FILL NAIL HOLES: If there are any nails that didn’t set into the wood and stick out, you’ll need to set them into the wood with a hammer and a nail setter.
Once all the nails are set, you can putty all of them with spackle so that the nail holes won’t show. Let the putty dry for 15-20 minutes before sanding.SANDING: Anything that isn’t smooth will need to be sanded down. That includes the putty from filling the nail holes and any of the boards that aren’t perfectly flush at the joins. Wipe down all of the trim after sanding to remove all the dust and debris before moving on to caulking. CAULK: Grab your caulk gun, caulk, caulk finishing tool and some painter’s tape. Run a fine bead of caul along each board join and use a caulk finishing tool to smooth it out. If you’re new to caulking, read this post before you start.
STEP 6: PAINT
We used a 4″ roller with a foam cabinet roller attachment to minimize any texture on the
We wanted this space to act as sort of a mud room. The garage empties into this hallway so it was a good location to catch all of our stuff as we get into the house.
These hooks were $9 each at Target and matched our style perfectly. We chose to attach them in the center of each opening of the molding, rather than at the
MAKE IT YOUR OWN: HOW TO MEASURE TO MAKE YOUR OWN BOARD AND BATTEN WALL[accordionitem title=”STEP 1: MEASURE THE WALL WIDTH”]Grab a measuring tape and measure the exact width. Here in Texas a lot of our homes have rounded corners, so we had to take about an inch and a half off the total width of the wall.
If we hadn’t, the last vertical board would hang over and it wouldn’t be a good look. I also wanted to bring the cap on the top over about half an inch, which we didn’t want to hang over either.
So when I say to measure the full width, I mean measure to where you want the top cap to stop. For us, that was 69″, as our wall was 70.5″.[/accordionitem] [accordionitem title=”STEP 2:CALCULATE HORIZONTAL SPACING”]
I wanted the spaces between each vertical board to be as close to 12″ as we could get. Now I need you to get your head in a math place.
- If each of my “1×4″s
areactually 3 1/4″ wide, so the first thing you have to account for is the end pieces: 6.5″.
- Divide the remaining inches by 12, then subtract by 1. I was down to 62.5″/12 = 5.2 -1 = 4. It won’t be exactly 12″ between each, but it’s as close as I was going to get.
- So 4 openings means I’ll need another 3 boards at 3 1/4″ (which adds up to 9.75″). 62.5″-9.75″ is 52 3/4″ divided over 4 openings is 13 1/8″ between each vertical board. This will be the measurement of your horizontal spacer boards [/accordionitem]
With the two of those plus the header at 3/4″ thick, all you have to do to figure out your vertical board height is subtract your desired height by 11 1/4″, so using my 78″ example, my vertical boards were 66 3/4″ long. [/accordionitem]
GET TO WORK
Now that you know how to install board and batten, is it something you’ll take on at your house? You know it doesn’t cost much, it can be done from start to finish in a weekend, and you don’t need to make any complicated wood cuts.
The hardest part for us was keeping the hallway clear of a nosy dog and little boy. If you tackle this project, post a picture and tag me on IG (@fixedonfresh). I would love to see how yours turns out!